Search found 700 matches

by jsa
Sat Mar 07, 2020 9:30 pm
Forum: Tuning the EEC....
Topic: Tuning a turbo'd 2001 3.0L Ranger with BE and QH
Replies: 32
Views: 1633

Re: Tuning a turbo'd 2001 3.0L Ranger with BE and QH

You need to change the scalars for injector high slope, low slope, breakpoint and minimum pulse width. You need to change the function for injector offset.

Edit, cross post with cgrey8
by jsa
Mon Mar 02, 2020 4:23 pm
Forum: EECGeeks
Topic: feedback please - moving to SQLite database files
Replies: 23
Views: 1122

Re: feedback please - moving to SQLite database files

Address [Address+bank] is an obvious one, as there can only be one thing at one address. How does that pan out for scratch registers that are assigned different values for different address ranges? How about something like MAP that might be defined multiple times for units of measure Hg", PSI, KPa ...
by jsa
Fri Feb 21, 2020 8:51 pm
Forum: EECGeeks
Topic: feedback please - moving to SQLite database files
Replies: 23
Views: 1122

Re: feedback please - moving to SQLite database files

For consideration and comments - Do you like SAD806x and its graphical format ??? I have used both at various times as well as the old BL disassembler. SAD & SAD806x are my preferred tools. Neither SAD or SAD806x give perfect results without the user intervening to control disassembly. Both give di...
by jsa
Thu Feb 20, 2020 10:36 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Pym is european, that is his primary use.
by jsa
Wed Feb 19, 2020 5:42 pm
Forum: Tuning the EEC....
Topic: Boost Sensor for Tuning
Replies: 21
Views: 685

Re: Boost Sensor for Tuning

I am disappointed with the repeatability of the Innovate stuff.
by jsa
Tue Feb 18, 2020 5:06 pm
Forum: Tuning the EEC....
Topic: Boost Sensor for Tuning
Replies: 21
Views: 685

Re: Boost Sensor for Tuning

I don't believe so. The 94 95 Mustang gets BP via internal calculations from other input. Looking to see what my options are to get boost into my logs/tune same as I would for AFR. All started because my Vac/Boost gauge reads Vac perfectly fine but never goes above 5 psi regardless of what the pull...
by jsa
Tue Feb 18, 2020 4:54 pm
Forum: Tuning the EEC....
Topic: Boost Sensor for Tuning
Replies: 21
Views: 685

Re: Boost Sensor for Tuning

It probably was too broad of a statement since there are exceptions, but it's not inaccurate for the vast majority of Ford EEC-IV/V strats. Or is that an overly broad, to the point of being inaccurate, statement? A lot of euro and aussie strats are speed density, so they have MAP. They could all be...
by jsa
Tue Feb 18, 2020 4:01 pm
Forum: Tuning the EEC....
Topic: Boost Sensor for Tuning
Replies: 21
Views: 685

Re: Boost Sensor for Tuning

Hello, Just trying to find out if I can wire in a boost sensor to help with tuning. Can't find anything online besides people asking where their MAP sensor is on a MAF car. Tuning a 95 Mustang Gt with Quarterhorse and Binary Editor. Thanks Does your application have a BAP sensor? How much boost do ...
by jsa
Tue Feb 18, 2020 3:56 pm
Forum: Tuning the EEC....
Topic: Boost Sensor for Tuning
Replies: 21
Views: 685

Re: Boost Sensor for Tuning

paulie wrote: The EEC is not capable of reading boost.
Incorrect.

The Escort Cosworth EEC-IV reads boost from its frequency type MAP sensor.
by jsa
Mon Feb 10, 2020 11:00 pm
Forum: EECGeeks
Topic: quick question about indexed ops
Replies: 7
Views: 394

Re: quick question about indexed ops

IIRC, 01 is odd so long indexed.
8F298 is my guess without looking up the handbook.
by jsa
Sat Feb 08, 2020 4:43 am
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Yeah, a bit messier than my first glance.

No worries, all in good time.
by jsa
Fri Feb 07, 2020 5:43 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Yes CARD bugs prior to the DADS post. Yes, I hear you on LDW. GUFB DEF available from BE site. http://www.eecanalyzer.net/strategies?view=download&format=raw&fileId=553 Yes comments that are output to listing are in CMT file. This is fairly typical of comments I place in DIR. These are not intended ...
by jsa
Fri Feb 07, 2020 5:09 am
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

I ran 4.04 on DADS.bin which is an old 32kb bin for the Mk5/6 Escort RS2000.

From a cold start it has disassembled the filler and strategy description at the end of the bin as a Table.
by jsa
Mon Feb 03, 2020 2:09 am
Forum: EECGeeks
Topic: GUFx FN393F
Replies: 5
Views: 342

Re: GUFx FN393F

For the ultimate in confidence log ECT.
The equation will be the same as the ECT payload.
by jsa
Sun Feb 02, 2020 6:50 am
Forum: EECGeeks
Topic: ROM1 address
Replies: 19
Views: 866

Re: ROM1 address

No worries. The thanks really goes to those who have done all the ground work for the info I shared.
by jsa
Sun Feb 02, 2020 5:02 am
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

DIR

Code: Select all

timer BA73 BBA6 : W N
4.04 LST null

Code: Select all

b999: a1,73,ba,30         ldw   R30,ba73         R30 = @(null);
3.08

Code: Select all

b999: a1,73,ba,30         ldw   R30,ba73         R30 = ba73;
by jsa
Sun Feb 02, 2020 4:46 am
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

DIR rbase f6 cf34 4.04 LST 4b b1ec: 9b,f6,4b,be cmpb Rbe,[Rf6+4b] b1f0: d9,0b jgtu b1fd if (ATMR1 > 4b) goto b1fd; 3.08 LST cf7f b1ec: 9b,f6,4b,be cmpb Rbe,[Rf6+4b] b1f0: d9,0b jgtu b1fd if (ATMR1 > [cf7f]) goto b1fd;
by jsa
Sun Feb 02, 2020 4:31 am
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

DIR WORD 8C62 8C6D LST 4.04 8c61: ff,fa word faff 8c63: 02,fc word fc02 8c65: 01,7d word 7d01 8c67: 01,80 word 8001 8c69: f0,55 word 55f0 8c6b: a0,40 word 40a0 8c6d: 78 byte 78 LST 3.08 8c61: ff ??? 8c62: fa,02 word 2fa 8c64: fc,01 word 1fc 8c66: 7d,01 word 17d 8c68: 80,f0 word f080 8c6a: 55,a0 word...
by jsa
Sat Feb 01, 2020 10:16 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

DIR SYM 4A "HSO_Hdlr_Flgs" SYM 4A "HSO_B0_R4A" :T +0 # SYM 4A "HSO_Byps_time" :T +1 # SYM 4A "HSO_Byps_limit" :T +2 # SYM 4A "HSO_Immediate" :T +3 # SYM 4A "HSO_No_service" :T +4 # SYM 4A "HSO_Late_output" :T +5 # SYM 4A "HSO_Queued" :T +6 # SYM 4A "HSO_No_queue" :T +7 # LST 4.04 55b6: 71,20,4a an2b...
by jsa
Sat Feb 01, 2020 9:39 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Multitasking between Bathurst 12hr and SAD. CARD 4.04 DIR SYM D5 "Flag_0" :T +0 SYM D5 "Flag=1_No" :T +1 SYM D5 "Flag_B2" :T +2 SYM D5 "Flag_B3" :T +3 SYM D5 "Code_b_4" :T +4 SYM D5 "Code_b_5" :T +5 # SYM D5 "Code_B6" :T +6 SYM D5 "Flag_B6" :T +6 # SYM D5 "Code_B7" :T +7 SYM D5 "Flag_B7" :T +7 LST 4...
by jsa
Sat Feb 01, 2020 4:12 pm
Forum: EECGeeks
Topic: ROM1 address
Replies: 19
Views: 866

Re: ROM1 address

PDE, Have you got a tuned bin with unadjusted checksum or faulty rom hardware?
by jsa
Sat Feb 01, 2020 4:00 pm
Forum: EECGeeks
Topic: GUFx FN393F
Replies: 5
Views: 342

Re: GUFx FN393F

Which 2 defs are you comparing?

X*2 for this gufb function by the look of it.
by jsa
Sat Feb 01, 2020 12:19 am
Forum: EECGeeks
Topic: GUFx FN393F
Replies: 5
Views: 342

Re: GUFx FN393F

The X column units are as per ECT as ECT is the input for FN393F. The Y column units are compared to MULTMR so must be the same units as MULTMR. mSec or X/1024Sec. From TVRfans disassembly 4a32: 45,18,00,f0,32 ad3w R32,Rf0,18 R32 = Func1; 4a37: b0,b0,34 ldb R34,Rb0 R34 = ECT; 4a3a: ef,6f,eb call 35a...
by jsa
Fri Jan 31, 2020 2:24 am
Forum: EECGeeks
Topic: ROM1 address
Replies: 19
Views: 866

Re: ROM1 address

Looking at TVRfans GUFB/A9L disassembly; ############################################################ # ROM Checksum ############################################################ Do_Csum: 7844: 01,30 clrw R30 R30 = 0; 7846: 01,3c clrw R3c R3c = 0; # 7848: a1,6a,78,42 ldw R42,786a R42 = 786a; # Start ...
by jsa
Fri Jan 31, 2020 1:54 am
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD 4.0.4

Don't know what to do about flag bits - I'll reread your earlier posts and consider.....current rule isn't good enough. 2 further thoughts here; 1. ORB and AN2B in immediate address mode. Are they always used as bit manipulators? 2. Should SAD track where registers are operated on as flags in multi...
by jsa
Sat Jan 18, 2020 10:25 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD 4.0.4

Linux - Software packages ? Like what ? (I'm interested) Autocad and Solidworks are two that present a challenge, as a _lot_ of cash goes into acquiring those and a lot of time to customize to purpose. Applications that talk to industrial hardware like VSD's, BACnet, MODBUS, etc. A lot of those are...
by jsa
Sat Jan 18, 2020 9:49 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Cold start code scanning is doing a good Job. Code missed from 5DE7 to 5EF5. Vectors in structure from 5EF6. 70BE is not code. 4,6,8 has some misses with word sized sets. 65E0 2 sets of 3 in a row. 70BE 3 Words not code. 8C62 2 sets of 3 in a row, not 8C61. So it looks pretty good for a cold start w...
by jsa
Sat Jan 18, 2020 8:17 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Thank you for 4.04's. CARD cold start for both, check out L3BE3. an2w VS an2b by SAD Version 4.0.3c (31/12/2019) 3be3: 71,87,34 an2b R34,87 B3_R34 = 0; B4_R34 = 0; B5_R34 = 0; B6_R34 = 0; by SAD Version 4.0.4 (15/01/2020) 3bb3: 61,3f,fe,34 an2w R34,fe3f B6_R34 = 0; B7_R34 = 0; B0_R35 = 0; 3bb7: c7,7...
by jsa
Sat Jan 18, 2020 8:00 pm
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Good luck ! I gave up fighting with Windows a long while ago, and went Linux instead, and am trying to convince as many people as possible to do the same. (Yeah, I know, but I can't help pushing at least a little bit ! ) I have XP and 7 only in virtual machines (VirtualBox), used mostly for SAD bui...
by jsa
Sat Jan 04, 2020 8:09 am
Forum: EECGeeks
Topic: SAD disassembler progress
Replies: 165
Views: 10881

Re: SAD disassembler progress

Thanks.

I am fighting an update to my sons pc. Will add this to my list.