EECTuning.org

Raymond_B

It's tough, best way to tell is by doing a read TwEECer through the software and checking out the firmware level. Otherwise the only difference is a white sticker on base models. But you should be OK here on this board, just ask about someone if you are not sure.

Raymond_B

Same thing with a read tweecer correct ?

Raymond_B

Yes it appears that the driver is loading properly. So when you click read tweecer you get errors right ? Or if you click read eec you get errors right ? What happens if you try to do a write tweecer ?

Raymond_B

OK so with the key on you pug in the USB cable. Go into Window's device manager then USB devices and see if the TweECer is operating properly.

Raymond_B

When you do a read eec what happens ? What error do you get ?

Raymond_B

Get some green Scotchbrite and clean Both sides of the J-3 until you can just see a hint of Copper.

Raymond_B

Hi Dale, I do not see 450 or higher being that hard. That 421 probably could make 450 easily with the right cam. And the 360 was through an E4OD.

Locally do you mean for the cam ? I always like using Cam Motion, Terry has always done us Lightning guys right.

Raymond_B

A month or so ago I tuned a 421 CI Windsor in a 93 Lightning. It was naturally aspirated, big Pro Top Line Heads (or something like that) 42lb injectors and around 10.5:1 compression. The cam was waaay too small and running out of steam, but it still managed to make 360 hp and around 400 ft lbs of T...

Raymond_B

OK I see that, but have you tried my tests :) Also how clean is the J3 port ? I would clean it with some Green Scotchbrite until just a hint of Copper shows on both sides.

Raymond_B

So you wrote the same file to all 4 positions and it idles at 1200 correct ? Then when you put it to position 5 it still idles at 1200 ? Maybe try this just to make sure it's working correctly. Pos 1 500 rpm idle (I know it probably won't run long) Pos 2 1000 rpm idle Pos 3 1500 Pos 4 2000 And see w...

Raymond_B

The switch position with the dimple is 1 from there it's 2,3,4 and finally 5 which is off or stock.

If you write to the tweecer while in position 5 you will actually write to pos. 3.

Raymond_B

Thanks Chris ! Anyway I'll stop with this post since I'm not supposed to post any further "stupid" things or "stuff" that doesn't help. I will say that initially it looked like someone wanting to snoop on the TwEECer connection to snag commands going back and forth. That's why I posted what I did. W...

Raymond_B

So why didn't you post your question in that context Jeremy ? You said nothing other than giveio is pissing you off. Then when the others replied you tried to tell them how it works. I'm not trying to be an ass either........ Oh and sorry I have no idea how to help you and I will not write "stuff" a...

Raymond_B

There's no way STKR is going to give you any kind of access into the software/hardware setup. That is all proprietary and property of STKR.

Raymond_B

After removing the goo I use green Scotchbrite and clean the J-3 connector until just a hint of Copper shows. I don't care what anyone else says :) I don't know how many people have tried just an eraser and have issues....... Ryan, you only had to clean yours with an eraser since the J-3 connector w...

Raymond_B

Tim what operating system does the computer have ? Also have you checked to see where it is trying to install to ?

Raymond_B

OK good deal :) If it were me I would get the software loaded and just start looking at the items that can be changed. You mentioned idle, I would edit that scalar and download a file with just that change. That way you can get used to how the software works without changing anything major that coul...

Raymond_B

Every single one of those questions are here on the UBB, just have some patience, slow down, and do some searching. From your questions it doesn't appear you have even the basic understanding of what you bought, and that's not good being that you can do serious damage to your car. I'm not being rude...

Raymond_B

If you do a Read EEC it will automatically pick your strategy and display it in the lower right hand corner.

Raymond_B

The learning curve is pretty much vertical, but you need to start slow and research what you want to change. You wouldn't make a post on how to build a motor with a shortblock kit in front of you would ya :) Anyway define some goals, then research how to achieve those goals. Take some time and learn...

Raymond_B

I believe the WAY1 binary is the same, or if the pinout is the same you just load the VEX1 binary and tune from there since the TwEECer holds the entire ROM contents. Hey, I was just in the process of making a harness to run my (stroked) Bronco with a Tweec'd A9L and piggybacke WAY1 (to run my E4OD)...

Raymond_B

I have tried C&L's as a draw through a couple of times with HORRIBLE results. Finally had to go with a Pro-M.......

Raymond_B

Jose, when you installed the TwEECer did you do a Read EEC then write tweecer to each position ? If not then you might have one of Mike's test files loaded. Try doing that first (to each position), then do the dreaded clean the J-3 connector dance :) Let me know how it goes, I'm sure Mike will help ...

Raymond_B

T4M0 is a manual, here's one for sale on EBAY

http://cgi.ebay.com/ebaymotors/ws/eBayI ... gory=33596

Raymond_B

WHat type of MAP sensor ? I can get you one for GM type.

Raymond_B

Jamie from the website: System Requirements You will need to have a Desktop PC or Laptop with a functioning USB port or USB 32bit CardBus card, running Win98SE, Win2K or WinXP. We supply all the cables and software neccessary to flash your adapter with your latest tweaks. If you do a search on this ...

Raymond_B

Mike, Jamie and I could use your help. He's tried two different TwEECer's so we've ruled out hardware. He's cleaned the laptop and reloaded the software to try to eliminate corrupted file(s) to no avail. Next step is to try to run the vehicle with no data log since the real issue is the truck cuttin...

Raymond_B

Hi Kevin, it works and we made 440 HP with Josh's truck, but if it were me I'd keep the setup you have :)

Raymond_B

I think I see the problem !

Do you have a C3P1 processor ?

Raymond_B

Thanks Don, Dean has been through all of that with me :)

Mike and I are working on it.

Search found 60 matches

Re: Dead TwEECer R/T?