Search found 18 matches

by tcgrmt
Tue Sep 30, 2008 2:17 pm
Forum: Tuning the EEC....
Topic: X3Z Stock Electric Fan settings
Replies: 7
Views: 6755

Re: X3Z Stock Electric Fan settings

I got the instructions and will test my X3Z to see if it works. Was just wondering what the stock fan setting where?
by tcgrmt
Tue Sep 30, 2008 10:22 am
Forum: Tuning the EEC....
Topic: X3Z Stock Electric Fan settings
Replies: 7
Views: 6755

Re: X3Z Stock Electric Fan settings

Thanks! Couple of questions: 1. So with the EDFHP & HEDFHP fan switches set at "0" (stock setting) can I run a fan off the 41 pin or do I need these switch settings changed to "1"? 2. With these stock settings looks like the fan will kick on @ 242degF. What's the temp it will turn off (220 or 234 de...
by tcgrmt
Tue Sep 30, 2008 9:20 am
Forum: Tuning the EEC....
Topic: X3Z Stock Electric Fan settings
Replies: 7
Views: 6755

X3Z Stock Electric Fan settings

Looking for the stock X3Z electric fan settings: 1. What temp does the fan come on? 2. What temp does the fan shut off? 3. Other speed settings related to electric fan operation? I don't have a tweecer or other tuner, just trying to use pin 41 of my X3Z computer to run an electric fan with the stock...
by tcgrmt
Fri Apr 25, 2008 10:00 pm
Forum: Hardware Discussions
Topic: Removed unused wires from harness and now high idle
Replies: 1
Views: 2646

Removed unused wires from harness and now high idle

This is on a track car. This last winter I went thru the wiring harness and removed all the wiring that wasn't being used.

The car started right up but has a high idle of 1500 RPM?

Any ideas?

Thanks,

Rob
by tcgrmt
Sat Apr 30, 2005 4:57 pm
Forum: Hardware Discussions
Topic: What the hell is this "invaild variant type conversion&
Replies: 8
Views: 7998

What the hell is this "invaild variant type conversion&

This last revision is junk. Can't read any scalers because the text is out of the box. Now it won't datalog. When I open Calcon I get "invaild variant type conversion". What the hell is this?? I spend more time trying to get this damn program running then I do Tweec'n. Should I just go back to the o...
by tcgrmt
Sun Apr 24, 2005 4:29 pm
Forum: Tuning the EEC....
Topic: Using a Lighting MAF in a 93 Mustang
Replies: 9
Views: 9302

Was hoping I could use an Andersen Power Pipe, the 4" version.

Did you use 4" tubing from the meter to the throtle body?
by tcgrmt
Sun Apr 24, 2005 3:51 pm
Forum: Tuning the EEC....
Topic: idle setting and eec analizer
Replies: 26
Views: 27661

86gt In reading the EEC Analyzer directions under TB Airflow & ISC: "Unplug the Idle Speed Controller (ISC) and distributor spout so that you can datalog the base idle. Now start the car and datalog the idle RPM and Mass Air Flow (MAF) voltage at normal operating temperatures." So do I need the dist...
by tcgrmt
Sun Apr 24, 2005 9:34 am
Forum: Tuning the EEC....
Topic: idle setting and eec analizer
Replies: 26
Views: 27661

In reading the EEC Analyzer directions under TB Airflow & ISC: "Unplug the Idle Speed Controller (ISC) and distributor spout so that you can datalog the base idle. Now start the car and datalog the idle RPM and Mass Air Flow (MAF) voltage at normal operating temperatures." So do I need the distribut...
by tcgrmt
Sat Apr 23, 2005 8:10 am
Forum: Tuning the EEC....
Topic: Oil in TFS intake
Replies: 4
Views: 5568

Seems to be a common problem with 302 strokers.

Lot of good info here:

http://corner-carvers.com/forums/showth ... hlight=pcv

I purchased a 3/8" air compressor water separator from Lowe's and installed it on my new Holley EFI intake and plumbed the PVC hose to it.
by tcgrmt
Fri Apr 22, 2005 8:23 pm
Forum: Tuning the EEC....
Topic: Using a Lighting MAF in a 93 Mustang
Replies: 9
Views: 9302

Using a Lighting MAF in a 93 Mustang

Anyone running a Ligthing 90MM MAF in a N/A 93' Mustang?

Looking for info on intake plumbing used to install.

Thanks,

Rob
by tcgrmt
Sun Apr 11, 2004 6:11 pm
Forum: Hardware Discussions
Topic: 1.3A7 w/A8 Calcon doesn't work
Replies: 1
Views: 2889

1.3A7 w/A8 Calcon doesn't work

Ok, I have been using 1.2 b3 without any problems. I loaded 1.3A7 w/A8 upgrade and I can't get the new version of CalCon to work.

Any suggustions?

Thanks,

Rob
by tcgrmt
Sun May 11, 2003 6:45 pm
Forum: Tuning the EEC....
Topic: Clearing the KAM
Replies: 13
Views: 16184

You need to pull the USB connection to your computer also. It didn't work for me until I pulled the USB to the laptop. It must supply some power to the KAM.
by tcgrmt
Wed Nov 13, 2002 3:46 pm
Forum: Hardware Discussions
Topic: calcon not working
Replies: 10
Views: 12716

what processor to you have?
by tcgrmt
Sat Oct 26, 2002 3:34 pm
Forum: Tuning the EEC....
Topic: Printing my Set-Up
Replies: 1
Views: 4326

Printing my Set-Up

Is there a way to print the screens so I can keep a hard copy record of the changes and notes?

Thanks,

Rob
by tcgrmt
Thu Oct 24, 2002 9:09 am
Forum: Hardware Discussions
Topic: calcon not working
Replies: 10
Views: 12716

I had the same problem, try this via a post Mike G. sent me on Yahoo tweecer group:

In the yahoo group tweecer look under files>software updates> for file A9LPL.DBF. Download this file to replace the one in your STKR>DATA folder.

This worked for me.

Good Luck, Happy Tuning!!
by tcgrmt
Thu Oct 24, 2002 7:38 am
Forum: Hardware Discussions
Topic: CalEdit RT Datalog Payloads and CalCon A/F Ratio
Replies: 0
Views: 3251

CalEdit RT Datalog Payloads and CalCon A/F Ratio

Why can't I select any RT Datalog payloads in CalEdit?

Also when I get my DIY_WBO2 unit done and connected via my EVP port will it show up on my CalCon A/F Display?

Thanks!!
by tcgrmt
Sat Oct 19, 2002 9:35 am
Forum: Tuning the EEC....
Topic: X3Z Basic set-up
Replies: 2
Views: 5293

X3Z Basic set-up

Mike,

Great product, it's made all the difference for my car with just the basic changes I have picked up on the Yahoo Tweecer group. I found a basic setup you posted under FAQ's for the ZOA (94-95). Would these apply to my X3Z 93' Cobra?

Thanks,

Rob
by tcgrmt
Fri Oct 18, 2002 2:47 pm
Forum: Tuning the EEC....
Topic: 88-93, 94-95 EEC IV and EEC V sections please??!!
Replies: 9
Views: 12894

:twisted: A X3Z group would be nice :!: