I'm not sure this is appropriate - but I'm sure there's someone there that can answer my question.
I going to convert my '68 F25 pickup to TBI. I has a midly build 390 in it right now. I considering the Mass-Flo system because is just about the only Mass Flow EFI system I could find. If I want to program it (and I do) they recommended using the Tweecer.
Mass-Flo seems to make a realtively simple, inexpensive and complete package and the Tweecer seems like a good tool for programming it.
Am I crazy? My wife says I am - but am I really?
Peter
Moderators: EDS50, cgrey8, 2Shaker, Jon 94GT
To answer your last question, yes, you are crazy.
But you're not alone, as there are many crazed individuals out there, like yourself, including myself. What I would do, instead of considering this strange ass Mass-Flo system is to run the stock EEC-IV system that Ford created for '86-93 Mustangs. Believe me, I've studied this quite a bit since I've owned a '71 Mach 1 for over 12 years. If you can find a good single plane intake for the 390, have it drilled for injectors in each intake port. Try to mimic what others have done for Edelbrock Victor Jr. intakes when converting to EFI. But definitely try to use utilize the EEC-IV setup... major power to be had for very little investment. The TwEECer bolts right up to it too.
But you're not alone, as there are many crazed individuals out there, like yourself, including myself. What I would do, instead of considering this strange ass Mass-Flo system is to run the stock EEC-IV system that Ford created for '86-93 Mustangs. Believe me, I've studied this quite a bit since I've owned a '71 Mach 1 for over 12 years. If you can find a good single plane intake for the 390, have it drilled for injectors in each intake port. Try to mimic what others have done for Edelbrock Victor Jr. intakes when converting to EFI. But definitely try to use utilize the EEC-IV setup... major power to be had for very little investment. The TwEECer bolts right up to it too.
'89 Fox: 8.6:1 306, GT-40 lower, Blowzilla 2.2, ProM 92mm MAF, 90mm TB, LU80s, TwEECed A9L w/EDIS8
'79 Bronco: 8.5:1 408C-2V, Lightning lower, Cobra upper, LMAF, 65mm TB, 24# injectors, EDIS8, Moates F3, single O2
'66 Mustang: 10.5:1 289, Victor Jr. EFI intake, 90mm TB, LMAF, 30# injectors, CDAN4 TwEECed
'00 Mountaineer: 9.2:1 302, ported Perf. RPM2, LMAF, 65mm TB, LU24As, READ0, QH currently
'08 & '09 Buell XB12Ss, 1125CR: DDFI3 tuned via TunerPro RT
'79 Bronco: 8.5:1 408C-2V, Lightning lower, Cobra upper, LMAF, 65mm TB, 24# injectors, EDIS8, Moates F3, single O2
'66 Mustang: 10.5:1 289, Victor Jr. EFI intake, 90mm TB, LMAF, 30# injectors, CDAN4 TwEECed
'00 Mountaineer: 9.2:1 302, ported Perf. RPM2, LMAF, 65mm TB, LU24As, READ0, QH currently
'08 & '09 Buell XB12Ss, 1125CR: DDFI3 tuned via TunerPro RT
I have just completed an EFI conversion on the Ford 400 motor in my '53 F100. I used an EEC-IV with a Tweecer. I also used a 2003 Cobra Throttle Body, a Sullivan Performance intake adaapter/plenum, 42# injectors and a 90mm lightning MAF. I still have some tuning to do, but it starts and runs.
Now I am looking for info on how to set my throttle Body Air Flow, and OL Startup fuel table.
My firing order is the same as a 5.0 HO, but you will have to change the firing order for a 390.
Now I am looking for info on how to set my throttle Body Air Flow, and OL Startup fuel table.
My firing order is the same as a 5.0 HO, but you will have to change the firing order for a 390.
1953 Ford F100, Ford 400 motor(434 cu inch), CHI-3V alloy heads, CHI-3V Intake, full roller valve train, SS valves, headers, EFI with Accufab Elliptical Blade TB, 90mm MAF, 42# injectors, BBK cold Air.
you might want to go research moreShaker666 wrote:What I would do, instead of considering this strange ass Mass-Flo system is to run the stock EEC-IV system that Ford created for '86-93 Mustangs.
Mass-Flo is a 1993 Mustang EFI system (EEC-IV) with a Pro-M air meter inside the throttle body.
Ryan McCormick
363CID, GT40P heads, Edelbrock Performer Intake, 75mm TB, 70mm Cobra MAF, 24lb injectors, 190LPH fuel pump, X3Z-EEC, mismatched headers, no-cats & 3" exhaust
Ford Fuel Injection.com
363CID, GT40P heads, Edelbrock Performer Intake, 75mm TB, 70mm Cobra MAF, 24lb injectors, 190LPH fuel pump, X3Z-EEC, mismatched headers, no-cats & 3" exhaust
Ford Fuel Injection.com
Who is online
Users browsing this forum: No registered users and 101 guests